DislikedMade a PIN for those using AP as exit it is used to avoid opening orders when price has reached the AP levels for James settings, the screenshot sPIN ettings is fine. regards {image} {file}Ignored
- #3,344
- Nov 15, 2016 1:35am Nov 15, 2016 1:35am
- | Commercial User | Joined Nov 2013 | 4,947 Posts
info@metacharttools,com
- #3,347
- Nov 15, 2016 1:43am Nov 15, 2016 1:43am
- Joined May 2014 | Status: Trader | 4,735 Posts
Take what you can, give nothing back
- #3,349
- Nov 15, 2016 2:07am Nov 15, 2016 2:07am
- | Commercial User | Joined Nov 2013 | 4,947 Posts
info@metacharttools,com
- #3,352
- Nov 15, 2016 3:01am Nov 15, 2016 3:01am
- | Commercial User | Joined Nov 2013 | 4,947 Posts
info@metacharttools,com
- #3,353
- Nov 15, 2016 3:09am Nov 15, 2016 3:09am
Wouldn't it make more sense to change APR and use it as a tri-state signal. State 1 gives a (opposite) signal to trade so add pin 3 to the entry pin list State 2 loose this signal if AP is 1/2 or 1/4 away from the opposite range (exit) so no more trades can be added State 3 opposite reached so signal turns and signals exit current trade (at the same time possible entry next trade)
- #3,357
- Nov 15, 2016 4:49am Nov 15, 2016 4:49am
- | Commercial User | Joined Nov 2013 | 4,947 Posts
Experimental EAX_APRangesv1.01 (only for daily range for now)
How it works (only in reverse mode !)
The pin starts with an opposite signal if the high or low is breached (bar close or direct depending on setting)
The pin is removed (set to NONE, blank) if the current price drops below of goes above the level set (FULL,THREEQUARTER,MIDDLE,QUARTER)
This will prevent EAX from adding more trades.
If the opposite range is reached the pin will of course give the opposite signal as exit.
You should set the pin as an exit trigger and add the pin to the entry conditions (but that is not needed)
You can also use the pin as an early exit if you set the EAX pin exit to "opposite or loss of signal" and the signal disappears on the selected level.
I would use the "signal on bar close" in that case.
How it works (only in reverse mode !)
The pin starts with an opposite signal if the high or low is breached (bar close or direct depending on setting)
The pin is removed (set to NONE, blank) if the current price drops below of goes above the level set (FULL,THREEQUARTER,MIDDLE,QUARTER)
This will prevent EAX from adding more trades.
If the opposite range is reached the pin will of course give the opposite signal as exit.
You should set the pin as an exit trigger and add the pin to the entry conditions (but that is not needed)
You can also use the pin as an early exit if you set the EAX pin exit to "opposite or loss of signal" and the signal disappears on the selected level.
I would use the "signal on bar close" in that case.
info@metacharttools,com
- #3,358
- Nov 15, 2016 5:19am Nov 15, 2016 5:19am
- | Commercial User | Joined Nov 2013 | 4,947 Posts
Ultimate hedging.....
no losses.
no losses.
info@metacharttools,com
- #3,359
- Nov 15, 2016 5:21am Nov 15, 2016 5:21am
Experimental EAX_APRangesv1.01 (only for daily range for now) How it works (only in reverse mode !) The pin starts with an opposite signal if the high or low is breached (bar close or direct depending on setting) The pin is removed (set to NONE, blank) if the current price drops below of goes above the level set (FULL,THREEQUARTER,MIDDLE,QUARTER) This will prevent EAX from adding more trades. If the opposite range is reached the pin will of course give the opposite signal as exit. You should set the pin as an exit trigger and add the pin to the...
