DislikedAeseme if i have no charts with any pins loaded from where i get those signals on pins? fixed {image} {image}Ignored
Always read Post #1
- #962
- Mar 18, 2016 5:45am Mar 18, 2016 5:45am
- Joined May 2014 | Status: Trader | 4,735 Posts
Take what you can, give nothing back
- #963
- Mar 18, 2016 10:38am Mar 18, 2016 10:38am
Aeseme if i have no charts with any pins loaded from where i get those signals on pins?
fixed {image} {image}
{quote} Cleared your Global Variables?
{quote} yes. sorry i forgot to mention
Have you already read the #Post 1 of this thread yet?
Is there an option to have all pins test as true before opening an order BUT exit on any?
Example : i have two pins, i need them both to tell the same direction signal before it validates, but at the same time exit/close order if any of them goes to other direction (not both of them).
Sort of having two of these 'ANY' buttons under the pins, like 'ANY IN' and 'ANY OUT' maybe? or like on the same line written 'ANY' and two small buttons beside it, one is 'IN' and the other is 'OUT', ANY [In][Out]... just suggesting ideas
Example : i have two pins, i need them both to tell the same direction signal before it validates, but at the same time exit/close order if any of them goes to other direction (not both of them).
Sort of having two of these 'ANY' buttons under the pins, like 'ANY IN' and 'ANY OUT' maybe? or like on the same line written 'ANY' and two small buttons beside it, one is 'IN' and the other is 'OUT', ANY [In][Out]... just suggesting ideas
- #966
- Mar 18, 2016 1:54pm Mar 18, 2016 1:54pm
- Joined Nov 2012 | Status: Coder | 8,521 Posts
Try don't lose pants never...
hmm 
, so on my example i have DashTZ on pin1 as entry with SnR (different TFs), and DashTZ as entry pin2 with TZ (different TFs), they both need to match in direction signal (pin1+pin2) before i get into an entry, then i should put pin3 as exit for SnR, and pin4 as exit for TZ, but how can i get the exit of pin3 OR pin4 to close a trade, while keeping 'pin1' AND 'pin2' both have to match before getting into an entry?
From your description, i should have both TZ and SnR on same pin1 as entry (but there is only 5 plugins inside each pin in DashTZ, and i'm testing against 5 Time Frames for SnR and 5 TFs for TZ)
So if i want to exit to either a 'TZ' OR 'SnR' reverse signal, i should have pin1 = entry for both TZ and SnR mixed up, and pin2 = exit for TZ, and pin3 = exit for SnR, and tick in EAX the 'Any' button, have only pin1 as entry ticked, and the 'x' buttons ticked on pin2 + pin3.
Makes sense, the only little prob is that there is only 5 plugins in each pin inside DashTZ right now... i just thought if EAX dashboard has the option to have the 'Any' button for entries separate from 'Any' button for exits, that way we can have the 'AND' for entries and 'OR' only for exits.
, so on my example i have DashTZ on pin1 as entry with SnR (different TFs), and DashTZ as entry pin2 with TZ (different TFs), they both need to match in direction signal (pin1+pin2) before i get into an entry, then i should put pin3 as exit for SnR, and pin4 as exit for TZ, but how can i get the exit of pin3 OR pin4 to close a trade, while keeping 'pin1' AND 'pin2' both have to match before getting into an entry?From your description, i should have both TZ and SnR on same pin1 as entry (but there is only 5 plugins inside each pin in DashTZ, and i'm testing against 5 Time Frames for SnR and 5 TFs for TZ)
So if i want to exit to either a 'TZ' OR 'SnR' reverse signal, i should have pin1 = entry for both TZ and SnR mixed up, and pin2 = exit for TZ, and pin3 = exit for SnR, and tick in EAX the 'Any' button, have only pin1 as entry ticked, and the 'x' buttons ticked on pin2 + pin3.
Makes sense, the only little prob is that there is only 5 plugins in each pin inside DashTZ right now... i just thought if EAX dashboard has the option to have the 'Any' button for entries separate from 'Any' button for exits, that way we can have the 'AND' for entries and 'OR' only for exits.
- #968
- Edited 5:17am Mar 19, 2016 4:24am | Edited 5:17am
- Joined Nov 2012 | Status: Coder | 8,521 Posts
hmm
2) pin 3/4 is possible in v0.66 because have priority no signal. Put PINs 3/4 in v0.72. Put in both PINs channels 100 and 101. In v0.66 put pin 1 channel 100 and pin 2 channel 101. Set in every pin priority 2 and priority no signal 1 and set pin out with EAX channel you will use for exit. If I'm not wrong exit will happen if one pin is with signal.
If this works then I'm the master because I never code DashTZ thinking can have this flexibility
Try don't lose pants never...
- #969
- Mar 20, 2016 5:17am Mar 20, 2016 5:17am
- Joined May 2014 | Status: Trader | 4,735 Posts
{quote} {quote} {quote} For cases like this one I included the "Reset [PINS]" button ..
Take what you can, give nothing back
- #975
- Mar 22, 2016 8:06pm Mar 22, 2016 8:06pm
- Joined Mar 2010 | Status: Trader | 2,261 Posts
thanks brother really appreciate
{quote} the maddash pins setting are same as given in this forum.. i downloaded that..i ll upload that also..but these setting did really bad on friday.. {file}
- #978
- Mar 30, 2016 12:39pm Mar 30, 2016 12:39pm
- Joined May 2014 | Status: Trader | 4,735 Posts
Take what you can, give nothing back
