Adding Retracements Extensions to High & Low of Bars

Dear Forex Traders

Can anyone assist in expanding the following attachment that Futurespec created for me please?

I am trying to show retracements value between the High And Low

What I would like displayed is underneath the current data of:

Open: 1.40567
High: 1.40628
Low: 1.40545
Close: 1.40626

0%: 1.40628 Formula = High of Bar
38%: 1.40659
1.40628 (H) - 1.40545 (L) = 0.00083 x 38% = 0.0003154 + High of Bar = 1.40659
50%: 1.40669
1.40628 (H) - 1.40545 (L) = 0.00083 x 50% = 0.0004150 + High of Bar = 1.40669
62%: 1.40679
1.40628 (H) - 1.40545 (L) = 0.00083 x 62% = 0.0005146 + High of Bar = 1.40679
100%: 1.40711
1.40628 (H) - 1.40545 (L) = 0.00083 x 100% = 0.00083 + High of Bar = 1.40711

0%: 1.40545
Formula = Low of Bar
38%: 1.40513
1.40628 (H) - 1.40545 (L) = 0.00083 x 38% = 0.0003154 - Low of Bar = 1.40513
50%: 1.40404
1.40628 (H) - 1.40545 (L) = 0.00083 x 50% = 0.0004150 - Low of Bar = 1.40404
62%: 1.40494
1.40628 (H) - 1.40545 (L) = 0.00083 x 62% = 0.0005146 - Low of Bar = 1.40494
100%: 1.40462
1.40628 (H) - 1.40545 (L) = 0.00083 x 100% = 0.00083 - Low of Bar = 1.40462

Criteria:
◘The numbers should be aligned for presentation purposes
◘It should allow you to display the data at any corner
◘You can choose bars back you would like to show this data for
◘Size can be modified if required
◘Perhaps most importantly, the flexibility to add or remove a % so I may want to add 150% but it only shows for green section without also showing in red section
◘I have added a screen shot from a previous software that showed this information


Attachment Attachment

Would have been better and easier if you had included the request in your original post!!!!!!!!!!!!!!!

M

Futurespec

Many thanks for modifying the template and yes I should have included all my specifications but did not want to take too much advantage of your generous service

However what I was after was the following:

◘To have displayed below the OHLC the date showing what the retracements values are for 38%, 50%, 62%, 76%, 100% for both up and down that is blue or red

Open: 1.59215
High: 1.59297
Low: 1.59193
Close: 1.59266
38%:
50%:
62%:
76%
100%:
38%:
50%:
62%
76%
100%

◘It should also allow you add or remove % - say if I wanted to add 200% or remove the 62%

◘Leave the retracement lines that you have created on the bar as this is useful but to have the data above displayed would make life easy

◘Currently also if I choose to have 2 bars back the retracement lines is fixed to the current bar only. This should move to the number of bars back you choose

Is this something you could assist me with?

Thanks a million for all that you have done so far

Another mod!
Last one!

M.

Futurespec

Thanks for all your efforts.

If you have no objections, I will post my requirements on another thread as there are still modifications to get to my desired indicator and I have taken enough of your time.

Regards