- #5,444
- Edited 5:05pm Sep 19, 2019 2:14pm | Edited 5:05pm
- | Joined Sep 2015 | Status: Trader | 1,863 Posts
$4 Trillion Gambling/Casino Everyday 1 reply
Doubling up method or playing casino 24 replies
casino journal 3 replies
Casino Forex 4 replies
Welcome To Casino ! 3 replies
Disliked{quote} I don't see what triggers a trade to open? what is your TS setup?Ignored
Disliked{quote} You have "Use_Pivot_Filter" selected, but don't have any Pivot line selected to filter your trades, so I expect this to trade the same as just a CycleV6 with entry on Ball 4, exit on Ball 1 and no other filters. Was that your intention?Ignored
Disliked{quote} You have "Use_Pivot_Filter" selected, but don't have any Pivot line selected to filter your trades, so I expect this to trade the same as just a CycleV6 with entry on Ball 4, exit on Ball 1 and no other filters. Was that your intention?Ignored
Disliked{image} Testing 4Ball entry and exit with 61,78 & 100 pivot lines. One trade so far... {image}Ignored
DislikedDear Gene and traders. I have some results this week. I started a new by complementing the existing settings. the v6 often missed the ball signal at H1, so I changed to M15 and trended from 200 Ma to longer Ma. Pivotline Trade has not yet devised a strategy, testing only the combination of MA and ball signal. Hgv1 seems to work well with the default settings. Custom settings using the Rsi filter may look a bit more advanced. And since my broker limited to 20 trades in the demo version, Hgv1 decided to test only two currency pairs, eurusd and usdjpy....Ignored
Disliked{quote} Interesting that you comment that H1 misses the Ball entry. From my experiences so far with Cycle_TS is that the trades are taken too early before the change in direction has been confirmed and going to m15 only makes it worse. I believe getting into the trade is not the problem, but getting out before repaint changes the status of the Ball, Marty takes over going the wrong direction and creates huge DDs, for example AUDCHF {image} The new manual SL built-in to V6a will help, but I'm more interested in some automatic SL settings, maybe using...Ignored
Disliked{quote} Hello JustUncleL. Thank you for quote. I think entry is also important but the exit is more important. If I traded automatically by setting Ball 12 Entry Ball 12Exit in H1, the swing ball shown in the chart was Ball 1 at that time and doesn't exit, but the ball was shown as Ball 12 the next day or a few days later and recorded a large DD. Furthermore, my broker only accepts 20 trades in the demo, so I think that the 9 Marty setup of the 28 currency pairs is not a normal test because it have to assume up to 280 trades. so I'll test two pairs.(EURUSD,...Ignored
Disliked{quote} Hello JustUncleL. Thank you for quote. I think entry is also important but the exit is more important. If I traded automatically by setting Ball 12 Entry Ball 12Exit in H1, the swing ball shown in the chart was Ball 1 at that time and doesn't exit, but the ball was shown as Ball 12 the next day or a few days later and recorded a large DD. Furthermore, my broker only accepts 20 trades in the demo, so I think that the 9 Marty setup of the 28 currency pairs is not a normal test because it have to assume up to 280 trades. so I'll test two pairs.(EURUSD,...Ignored
Disliked{quote} Your Broker has a very restrictive Demo account, I don't have any such restrictions on open trades on any of the Brokers Demo accounts I have tried: Pepperstone, GlobalPrime, OANDA and TradersWay. However, the first three Brokers will be subject to ASIC proposed Max Leverage and Min Margin restrictions that will apply in a month or so.Ignored
Disliked{quote} I used Pepperstone, but they noticed that they are no longer serving the Koreans. So I found another broker. But I won't be using a live account unless I'm sure about the demo. Thank you for good information. And I trust v6a.Ignored
Disliked{quote} I think you need to be a bit careful of 6a, it is very new and not tested much, we have already had one missing piece of code fixed so make sure you have the latest version from post #5434 with the manual TP/SL fix.Ignored