I do not use Stoch at all (though they are attached in my hourly charts). So, no digistoch also. May be I checked it out long back for couple of days and removed it (thats what I do to all the downloaded indicators!).
Regards,
chandra
Volatility indicators (histogram version and alerts needed) 155 replies
WOW! Your Speech Enabled Indicators - Voice/Alerts/Alarms are very Interesting. 2 replies
Best software for audio alerts based on indicators? 1 reply
Signals/alerts for indicators 2 replies
New Alerts for Indicators - Juice, DMI, MomentumVT 5 replies
DislikedHi Chandra, good indicator, but why in my MT the two texts are in the same position?
Thank you
OnireIgnored
DislikedHi Onire,
Possibly you have attached two indicators (or attached one but twice with different settings?). Then you have to change the TextPosition in the Indicator Parameters for one of them. Or just delete the indicators and re-attach while monitoring what causes this problem.
Regards,
chandraIgnored
DislikedHi Chandra,
when I put lispa2mtf in a new chart its all ok, but if a save the same chart as a template and then a load it in an other chart there is the problem.
The initial tamplate is imran_setup.tpl and then I add your indicator.
Thank you,
OnireIgnored
DislikedHi Onire,
The bad problem with MT4 is that when you save a template, all the Objects (trendlines, vertical/horizontal lines, arrows and texts...) in that chart are also saved. So, whenever there are objects, better not to use that chart for making template (so never make template with any LISPA in it). Remove LISPA. Then delete all objects. You can go to Objects List by right-clicking on the chart and delete whatever you don't like (the old ones; click on the Names tab or Object Tab to sort them and then you can delete just only one at a time!). Then attach LISPA.
Regards,
chandraIgnored
DislikedHi A777,
Here itself I will write what I know (which is not much). I am not in touch with Imran or anybody for a long time; though a few times I had email contact with two earlier active members, I never talked anything about the pooled account (I only read it here on FF). So, I do not know what happened. But I am sure it has nothing to do with the system. Most likely, the winnings gave Imran over-confidence and made him violate some most important basic rules of trading (on money management and averaging-down). If a single trade is involved using maximum money and 100 leverage, it has to make 100 pips loss before busting an account! 100 pips loss is not part of the system. Sometimes I also do, but I do it in smaller lots and it does not hurt that much when the averaged positions go bad. The danger of Martingale or semi-martingale, I suppose.
I don't think there is anything wrong with the method. Only few changes I would like to suggest:
1. The main condition I wrote long back is that use the signals ONLY after Consolidation Breakout or Curved Reversal (and double-top/double-bottom??). [This will force us to avoid trading in sideways market, choppy market, sharp reversals; unfortunately I cannot code a filter for that!!!]. As long as that is followed, it will be a successful system, even with just one Lag (Red is better I think).
2. After the singal with these two setups, the price must break further in the right direction (or after a correction a better entry can be used, if the indicator is still moving in the original direction). Or Yas1r method can be used: going to 1M chart and waiting for a correction+continuation using the blue or red Lag there ( http://www.forexfactory.com/showpost...postcount=6470 ).
3. No fixed SL. The SL has to be based on recent price levels (if it is too much for comfort, we HAVE to ignore that trade).
4. There is never adding more lots to losing situations (it is not part of the system anyway).
These conditions will make many systems work well. But the Lag will keep in trends longer that most other indicators. Currently I am busy and not trading much. But still working on finding simple controls to reduce losing trades, while able to catch big moves. This is the simplest so far I have come, but involves manual filtering. No other indicator is needed/useful! Lot of patience is needed. When we see a 100 or 200 pip move going without us, it is quite tempting to enter next time even without these setups, even worse if the move happens after kicking us out at our SL. Thats where the patience comes. Further simplification I am checking is to use a single Lag and the midpoint cross (above midpoint, look for longs only; below midpoint, look for shorts only. Can do the entries in next lower TF chart possibly. Seems simpler, but still the above conditions must be followed and so can't be automated!).
Hope this gives some ideas of what to look for.
Regards,
chandraIgnored
DislikedHello Chandra...I am just discovering this trading system and all the indicators, but would like to ask your help. I see so many updates, revisions, etc., I'm not sure which indicators to use.
Could you PM me (or respond in a post here) a list of the indicators I ought to be using if starting at this point (i.e. the latest updates, etc.)? I do have Imran's setup template which has what I need I suppose, but you have obviously added many things/updates since that was originally created, and I'd like to have the latest refinements if possible.
Thank you for your work on this and for sharing itIgnored
DislikedHello Chandra......
I am having an EA made the uses one of the lines from your Laguerre3-ACS1 indicator.
Is it possible to get the souce code from you?
I am willing to either....
1. Pay you a small price for it or
2. Offer you a copy of the EA when I am finished for you own personal use.
Please let me know your thoughts
Thanks in advance.....DamonIgnored
DislikedHi Damonl,
Glad to see that you like my indicator. Please check your PM.
Regards,
chandra
EDIT:
As far as I can think, there is no need to use any program other than Laguerre-ACS1 in any EA. This is my main program for almost all Laguerre related indicators/calculations. Within EA indicators are toooo easy to use without any timeframe restrictions. Just use the following lines of code:
Lag1 = iCustom(Symbol(), TF1, "Laguerre-ACS1", gamma, 200, 2, 0, Bar);
Lag2 = iCustom(Symbol(), TF2, "Laguerre-ACS1", gamma, 200, 2, 0, Bar);
Lag3 = iCustom(Symbol(), TF3, "Laguerre-ACS1", gamma, 200, 2, 0, Bar);
You can use any TF, any gamma, any Bar and any number of times this line can be added. The source code for any indi is generally not needed, but even the source code is available for my main Laguerre-ACS1 in the previous page. This is better than my old Laguerre3-ACS (if I rewrite it, I will write using this three simple lines!). So, you can get all the needed codes from here already. Good Luck with your EA.
Regards,
chandraIgnored
DislikedHi Chandra
Using the Lag Histo, its great. However when you place higher timeframe LagHistos on the chart , the lags go flat after a few minutes, is there anyway you can rectify this.
Regards
CitiIgnored