Hi brother aeseme, you are right, I mess up with settings. I reset to default and go through one by one, and now there is buy and sell position opened. And I believe GAP X as exit will works as well. Im sorry and thank you.
MagicGirl dashboard 221 replies
Help with dashboard style indicator 2 replies
Dashboard indicators 4 replies
Dashboard Indicator Required 1 reply
Dashboard/Grid in lower indictor window 6 replies
DislikedHi brother aeseme, you are right, I mess up with settings. I reset to default and go through one by one, and now there is buy and sell position opened. And I believe GAP X as exit will works as well. Im sorry and thank you.Ignored
DislikedAeseme when you have time can you try to reproduce this scenario?not sure why a new trade was taken before 15 min to pass.is set to take new only if in profit but H still must hold it for 15 min candle and 15 mintes since first order. {image}Ignored
Both were opened on different M15 candles.
There's no option (yet) to wait X minutes since first order open, the one related to hold since first open is "One order per candle bar", and it does not wait for X minutes, it waits for next X minutes candle, and "One order per round hour period", that waits for the next hour change.
The one related to wait in minutes is "New order after N minute(s) since last closed one".
I have plans to add scopes based on distance (Pips/%ADR) and minutes since last open order, but with no ETA by now.
Disliked{quote} You have "One order per candle bar" as a Hold[H] filter scope and M15 as candle time-frame. By looking at these orders times: 2016.02.16 14:43:17 (Opened in M15 candle bar from 2016.02.16 14:30:00 to 2016.02.16 14:44:59) 2016.02.16 14:48:46 (Opened in M15 candle bar from 2016.02.16 14:45:00 to 2016.02.16 14:59:59) Both were opened on different M15 candles. There's no option (yet) to wait X minutes since first order open, the one related to hold since first open is "One order per candle bar", and it does not wait for X minutes, it waits for...Ignored
DislikedHello aeseme and all! I am new in this thread. I read through most of the post and I am not so sure if my PINs are working since they are not showing anything. Are they working just fine or somewhere i went wrong? Didn't see any trades after i activated auto when i think the condition fits so I am a little lost. Thanks! {image}Ignored
Disliked{quote} Everything seems fine, all MADdash's with their corresponding PIN enabled as per their labels at their top left corner. PINS are not showing anything just because no alerts are being generated by MADdash (see the ALTERS labels in each MADdash chart, there's nothing below there). Sometimes you have to be patient, alerts are not being generated all the time and by the way, are 100% dependent on your current MADdash settings.Ignored
DislikedAseme :look at image ,,PIN one is active but not working properly,its giving wrong direction and still hang even time changed.. and how can other pins be active ???pin2 and pin3?? {image}Ignored
Disliked{quote} o ok thanks aeseme! just a little worried because i was watching the video in the first post, u had some highlighted ones in the second pin after u activated the maddash.Ignored
QuoteDislikedone more weird thing happens when i followed the exact steps in the video adding the maddash.
step 1. i use the maddash+pin template
step 2. i open the properties of maddash indi and load the settings
step 3. i open the properties of DBMultiASM_MADdash_PIN_v2.0 and set the (e.g first one to PIN 1)
right after this step the entire MT4 will shut itself down.
QuoteDislikedto overcome this, i did step 1 and 2 for all the 3 PINS i wanted. then restart the whole MT4. then manually drag DBMultiASM_MADdash_PIN_v2.0 to each of the PIN charts again. hope i am not wrong anywhere.
Disliked{quote} If I understood you correctly, by doing this you will end up with 2 DBMultiASM_MADdash_PIN_v2.0's on each chart because the MADdash+PIN template already have both, but if that worked for you, it's OK, only drawback would be a little extra waste of resources. ..Ignored
Disliked{quote} {image} If you have the trail settings like in the picture, the trailing distance will be the last (or higher) lock level. The video doesn't show your trail settings nor all your lock levels, but it seems that you have the trail settings like in the picture and your higher lock level is $30... and if that's correct, what's on your video is OK. Now, if my guessing isn't correct, you've hit a bugIgnored
Disliked{quote} after i restarted the MT4, the DBMultiASM_MADdash_PIN_v2.0 disappears from the list of indicators so i think there is only one. I am going to sit by here and observe it hope it opens a trade soon then it will make me feel betterIgnored